I think there is a post about this in the turbo section. Mr_astra, Turblue, OPL20T and Rhino (to my knowledge) have all had there pipes done.
Hey guys, just wondering what size exhaust size is recommended for the SRiT? im planning on getting one soon and just needed some guidence on what size is best for my car?
Also does any1 know wot type of panel air filter is better outta the BMC and the KN? or is it just personal preference?
Warning: This is an Old Thread
This discussion is older than 120 days. information contained in it may no longer be current . Please think of the children before resurrecting this ancient thread!
2003 Astra SRi Turbo
163.3fwkW@ 15psi
Winton Short Track: 1:17:62 (Street tyres)
Winton Long Track: 1:49:42 (Street tyres)
Wakefield Park: 1:18:46 (Street tyres)
I think there is a post about this in the turbo section. Mr_astra, Turblue, OPL20T and Rhino (to my knowledge) have all had there pipes done.
Nick
MY03 - Astra SRi - Black...Sleek...
Mate the debate about exhaust can go on for days.
Some guys have 3 inches straight through, some have 2.5inches.
Ive got a 3 inch dump pipe to a 3 inch bend flex, into a 3 inch wide body high flow cat and a 3 inch cat back.
Currently Playing:
SUEDE@VBar Sat nights
Seductive Fridays Monthly@Space
Goodies@Goodbar Friday nights
Always have a read through this...found it helpful when i was researching exhausts.
Exhausts...
Nick
MY03 - Astra SRi - Black...Sleek...
Personally if you intend on doing other performance mods after the exhaust. i'd go the 3" coz you don't wanna end up changing the exhaust twice coz u got too much back pressure.
Gee Degen, that's a great signature you got there! maybe FLY_SRi would be interested in also clicking on that to find out more info. :wink:
Victorian Events Co-Ordinator... or anti-social behavioral disorder therapist
I have a 3 inch cat back system with Two resornators as well . Keeps it quiet but sounds very nice when you get up it .
I also have a K&N panel filter , but there isnt a huge difference between the two so personal choice mate.
i have a 3" from turbo no pre cat 3"into dump pipe with 3" flex bend into a 3" high flo cat continued into at 3" to the petrol tank then 2.5"into a 2.5" baffle muffler to keep it quieter inside the car and i also have a 2.5" chrome end peice with carbon fiber through it to reduce the noise and make is sound rough at the same time at low revs .
i also have a replacement K&N pannel filter and AmD re-map with a few glitches hee hee. but its all good wtill waiting for new upgrade map..
hope this helps ya out champ.
***OPL-20T*** Number Plates FOR SALE.
For a turbo car, there is no such thing as to big, only to loud. At the end of the article mentioned above it says,
"Add half an inch to the pipe diameter to optimize for nitrous oxide use. For turbocharged engines, 2.5 inches is the minimum size pipe to run, even for the smaller engines. For 2000cc and bigger engines, 3 inches works well and for bigger engines, the biggest (usually 3.5 inch) you can find is appropriate."
Don't go smaller than 2.5 inches, but 3 is the wat to go.
Epsilon Renntech
2003 Astra SRi-T - The Phantom
EMTRON ECU
Borg Warner EFR7163 & EFR9180
Tuned by Scott @ Insight Motorsports
There are currently 1 users browsing this thread. (0 members and 1 guests)